View L6599ADTR_782001.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

september 2010 doc id 15308 rev 5 1/36 36 l6599a improved high-voltage resonant controller features 50% duty cycle, variable frequency control of resonant half-bridge high-accuracy oscillator up to 500 khz operating frequency two-level ocp: frequency-shift and latched shutdown interface with pfc controller latched disable input burst-mode operation at light load input for power-on/off sequencing or brownout protection non-linear soft-start for monotonic output voltage rise 600 v-rail compatible high-side gate driver with integrated bootstrap diode and high dv/dt immunity -300/800 ma high-side and low-side gate drivers with uvlo pull-down dip16, so16n package application lcd and pdp tv desktop pc, entry-level server telecom smps high efficiency industrial smps ac-dc adapter, open frame smps dip16 so16n table 1. device summary order codes package packaging l6599ad so16n tube L6599ADTR so16n tape and reel l6599an dip16 tube www.st.com
contents l6599a 2/36 doc id 15308 rev 5 contents 1 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.1 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.2 thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 typical electrical performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 7 application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7.1 oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7.2 operation at no load or very light load . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 7.3 soft-start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 7.4 current sense, ocp and olp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 7.5 latched shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 7.6 line sensing function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 7.7 bootstrap section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 8 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 9 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
l6599a description doc id 15308 rev 5 3/36 1 description the l6599a is an improved revision of the previous l6599. it is a double-ended controller specific for the series-resonant half-bridge topology. it provides 50% complementary duty cycle: the high-side switch and the low-side switch are driven on/off 180 out-of-phase for exactly the same time. output voltage regulation is obtained by modulating the operating frequency. a fixed dead-time inserted between the turn-off of one switch and the turn-on of the other one guarantees soft-switching and enables high-frequency operation. to drive the high-side switch with the bootstrap approach, the ic incorporates a high-voltage floating structure able to withstand more than 600 v with a synchronous-driven high-voltage dmos that replaces the external fast-recovery bootstrap diode. the ic enables the designer to set the operating frequency range of the converter by means of an externally programmable oscillator. at start-up, to prevent uncontrolled inrush current, the switching frequency starts from a programmable maximum value and progressively decays until it reaches the steady-state value determined by the control loop. this frequency shift is non linear to minimize output voltage overshoots; its duration is programmable as well. at light load the ic may enter a controlled burst-mode operation that keeps the converter input consumption to a minimum. ic?s functions include a not-latched active-low di sable input with current hysteresis useful for power sequencing or for brownout protection, a current sense input for ocp with frequency shift and delayed shutdown with automatic restart. a higher level ocp latches off the ic if the first-level protection is not sufficient to control the primary current. their combination offers complete protection against overload and short circuits. an additional latched disable input (dis) allows easy implementation of otp and/or ovp. an interface with the pfc controller is provided that enables to switch off the pre-regulator during fault conditions, such as ocp shutdown and dis high, or during burst-mode operation.
block diagram l6599a 4/36 doc id 15308 rev 5 2 block diagram figure 1. block diagram 9ff 9 %227 +9 ',6$%/( ',6 287 & %227 /&7$1. &,5&8,7 89 '(7(&7,21 9ff +9* 6<1&+521286 %227675$3 ',2'( +9* '5,9(5 ',6 /(9(/ 6+,)7(5 9 64 5 89/2 89/ 2 ',6 9 9 67$1'%< 67%< '5,9,1* *1' ,iplq ,6(1 9 /9* /9* '5,9(5 &vv '($' 7,0( 5)pl q 46 5 89/2 ,6(1b',6 '5,9,1* /2*,& 9 67$1'%< ',6 ,6(1b',6 9 3)&b6723 &) &21752/ /2*,& /,1(b2. 9 ?$ 9 2&3 9&2 /,1( '(/$< !-v
l6599a pin connection doc id 15308 rev 5 5/36 3 pin connection figure 2. pin connection (top view) table 2. pin description pin n# type function 1css soft-start. this pin connects an external capacitor to gnd and a resistor to rfmin (pin 4) that set both the maximum oscillator frequency and the time constant for the frequency shift that occurs as the chip starts up (soft-start). an internal switch discharges this capacitor every time the chip turns off (vcc < uvlo, line < 1.24 v or > 6 v, dis > 1.85 v, isen > 1.5 v, delay > 2 v) to make sure it will be soft-started next, and when the voltage on the current sense pin (isen) exceeds 0.8 v, as long as it stays above 0.75 v. 2delay delayed shutdown upon overcurrent. a capacitor and a resistor are connected from this pin to gnd to set the maximum duration of an overcurrent condition before the ic stops switching and the delay after which the ic restarts switching. ev ery time the voltage on the isen pin exceeds 0.8 v the capacitor is charged by an internal 150 a current generator and is slowly discharged by the external resistor. if the voltage on the pin reaches 2 v, the soft start capacitor is completely discharged so that the switching frequency is pushed to its maximum value and the 150 a is kept always on. as the vo ltage on the pin exceeds 3.5 v the ic stops switching and the internal generator is turned off, so that the voltage on the pin will decay because of the external resistor. the ic will be soft- restarted as the voltage drops below 0.3 v. in this way, under short circuit conditions, the converter will work intermittently with very low input average power. 3cf timing capacitor. a capacitor connecte d from this pin to gnd is charged and discharged by internal current generators programmed by the external network connected to pin 4 (rfmin) and determines the switching frequency of the converter. !-v '.$ #ss $%,!9 34"9 )3%. ,).% ,6' 6"//4 (6' .# 6cc 0&#?34/0 /54 $)3 #& 2&min
pin connection l6599a 6/36 doc id 15308 rev 5 4rfmin minimum oscillator frequency setting. this pin provides a precise 2 v reference and a resistor connected from this pin to gnd defines a current that is used to set the minimum oscillator frequency. to close the feedback loop that regulates the converter output voltage by modulating the oscillator frequency, the phototrans istor of an optocoupler will be connected to this pin through a resistor. the value of this resistor will set the maximum operating frequency. an r-c series connected from this pin to gnd sets frequency shift at start-up to prevent excessive energy inrush (soft-start). 5stby burst-mode operation threshold. the pin senses some voltage related to the feedback control, which is compared to an internal reference (1.24 v). if the voltage on the pin is lower than the reference, the ic enters an idle state and its quiescent current is reduced. the chip restarts switching as the voltage exceeds the reference by 50 mv. soft-start is not invoked. this function realizes burst-mode operation when the load falls below a level that can be programmed by properly choosing the resistor connecting the optocoupler to pin rfmin (see block diagram). tie the pin to rfmin if burst-mode is not used. 6 isen current sense input. the pin senses the primary current though a sense resistor or a capacitive divider for lossless sensing. this input is not intended for a cycle-by-cycle control; hence the voltage signal must be filtered to get average current inform ation. as the voltage exceeds a 0.8 v threshold (with 50 mv hysteresis), the soft-start capacitor connected to pin 1 is internally discharged: the frequency increases hence limiting the power throughput. under output short circuit, this normally results in a nearly constant peak primary current. this condition is allowed for a maximum time set at pin 2. if the current keeps on building up despite this frequency increase, a second comparator referenced at 1.5 v latches the device off and brings its consumption almost to a ?before start-up? level. the information is latched and it is necessary to recycle the supply voltage of the ic to enable it to restart: t he latch is removed as the voltage on the vcc pin goes below the uvlo threshold. tie the pin to gnd if the function is not used. 7line line sensing input. the pin is to be connected to the high-voltage input bus with a resistor divider to perform ei ther ac or dc (in systems with pfc) brownout protection. a voltage below 1. 24 v shuts down (not latched) the ic, lowers its consumption and discharges the soft-start capacitor. ic?s operation is re-enabled (soft-started) as the voltage exceeds 1.24 v. the comparator is provided with current h ysteresis: an internal 13 a current generator is on as long as the voltage applied at the pin is below 1.24 v and is off if this value is exceeded. bypass the pin with a capacitor to gnd to reduce noise pick-up. the voltage on the pin is top-limited by an internal zener. activating the zener causes the ic to shut down (not latched). bias the pin between 1.24 and 6 v if the function is not used. 8dis latched device shutdown. internally the pin connects a comparator that, when the voltage on the pin exceeds 1. 85 v, shuts the ic down and brings its consumption almost to a ?before start-up? level. the information is latched and it is necessary to recycle th e supply voltage of the ic to enable it to restart: the latch is removed as the voltage on the vcc pin goes below the uvlo threshold. tie the pin to gnd if the function is not used. table 2. pin description (continued) pin n# type function
l6599a pin connection doc id 15308 rev 5 7/36 9pfc_stop open-drain on/off control of pfc cont roller. this pin, normally open, is intended for stopping the pfc controller, for protection purpose or during burst-mode operation. it goes low when the ic is shut down by dis>1.85 v, isen > 1.5 v, line > 6 v and stby < 1.24 v. the pin is pulled low also when the voltage on pin delay exceeds 2 v and goes back open as the voltage falls below 0.3 v. during uvlo, it is open. leave the pin unconnected if not used. 10 gnd chip ground. current return for both the low-side gate-drive current and the bias current of the ic. all of the ground connections of the bias components should be tied to a track going to this pin and kept separate from any pulsed current return. 11 lvg low-side gate-drive output. the driver is capable of 0.3 a min. source and 0.8 a min. sink peak current to driv e the lower mosfet of the half-bridge leg. the pin is actively pulled to gnd during uvlo. 12 vcc supply voltage of both the signal part of the ic and the low-side gate driver. sometimes a small bypass capaci tor (0.1 f typ.) to gnd might be useful to get a clean bias voltage for the signal part of the ic. 13 n.c. high-voltage spacer. the pin is not inte rnally connected to isolate the high- voltage pin and ease compliance with safety regulations (creepage distance) on the pcb. 14 out high-side gate-drive floating ground. cu rrent return for the high-side gate- drive current. layout carefully the connection of this pin to avoid too large spikes below ground. 15 hvg high-side floating gate-drive output. t he driver is capable of 0.3 a min. source and 0.8 a min. sink peak curren t to drive the upper mosfet of the half-bridge leg. a resistor interna lly connected to pin 14 (out) ensures that the pin is not floating during uvlo. 16 vboot high-side gate-drive floating supply voltage. the bootstrap capacitor connected between this pin and pin 14 (out) is fed by an internal synchronous bootstrap diode driven in-p hase with the low-side gate-drive. this patented structure replaces the normally used external diode. table 2. pin description (continued) pin n# type function
electrical data l6599a 8/36 doc id 15308 rev 5 4 electrical data 4.1 absolute maximum ratings note: esd immunity for pins 14, 15 and 16 is guaranteed up to 900 v. 4.2 thermal data table 3. absolute maximum rating symbol pin parameter value unit v boot 16 floating supply voltage -1 to 618 v v out 14 floating ground voltage -3 to v boot -18 v dv out /dt 14 floating ground max. slew rate 50 v/ns vcc 12 ic supply voltage (icc = 25 ma) self-limited v v pfc_stop 9 maximum voltage (pin open) -0.3 to vcc v i pfc_stop 9 maximum sink current (pin low) self-limited a v linemax 7 maximum pin voltage (ipin 1 ma) self-limited v i rfmin 4 maximum source current 2 ma --- 1 to 6, 8 analog inputs and outputs -0.3 to 5 v ptot power dissipation @t a = 70 c (dip16) 1 w power dissipation @t a = 50 c (so16) 0.83 tj junction temperature operating range -40 to 150 c tstg storage temperature -55 to 150 c table 4. thermal data symbol parameter value unit r th(ja) max. thermal resistance junction to ambient (dip16) 80 c/w max. thermal resistance juncti on to ambient (so16) 120 c/w
l6599a electrical characteristics doc id 15308 rev 5 9/36 5 electrical characteristics t j = 0 to 105 c, vcc = 15 v, vboot = 15 v, c hvg = c lvg = 1 nf; c f = 470 pf; r rfmin = 12 k ; unless otherwise specified. table 5. electrical characteristics symbol parameter test condition min. typ. max. unit ic supply voltage vcc operating range after device turn-on 8.85 16 v vcc on turn-on threshold voltage rising 10 10.7 11.4 v vcc off turn-off threshold voltage falling 7.45 8.15 8.85 v hys hysteresis 2.55 v v z vcc clamp voltage iclamp = 15 ma 16 17 17.9 v supply current i start-up start-up current before device turn-on vcc = vcc on - 0.2 v 200 250 a i q quiescent current device on, v stby = 1 v 1.5 2 ma i op operating current device on, v stby = v rfmin 3.5 5 ma i q residual consumption v dis > 1.85 v or v delay > 3.5 v or v line < 1.24 v or v line = v clamp 300 400 a high-side floating gate-drive supply i lkboot v boot pin leakage current v boot = 580 v 5 a i lkout out pin leakage current v out = 562 v 5 a r ds(on) synchronous bootstrap diode on-resistance v lvg = high 150 overcurrent comparator i isen input bias current v isen = 0 to v isendis -1 a t leb leading edge blanking after v hvg and v lvg low- to-high transition 250 ns v isenx frequency shift threshold voltage rising (1) 0.77 0.8 0.83 v hysteresis voltage falling 50 mv v isendis latch off threshold voltage rising (1) 1.45 1.5 1.55 v td (h-l) delay to output 300 400 ns line sensing vth threshold voltage voltage rising or falling (1) 1.2 1.24 1.28 v i hys current hysteresis v line = 1.1 v 101316a v clamp clamp level i line = 1 ma 6 8 v
electrical characteristics l6599a 10/36 doc id 15308 rev 5 symbol parameter test condition min. typ. max. unit dis function i dis input bias current v dis = 0 to vth -1 a vth disable threshold voltage rising (1) 1.78 1.85 1.92 v oscillator d output duty cycle both hvg and lvg 48 50 52 % f osc oscillation frequency 58.2 60 61.8 khz r rfmin = 2.7 k 240 250 260 t d dead-time between hvg and lvg 0.2 0.3 0.4 s v cfp peak value 3.9 v v cfv valley value 0.9 v v ref voltage reference at pin 4 (1) 1.93 2 2.07 v i ref = - 2 ma (1) 1.93 2 2.07 k m current mirroring ratio 1 a/a pfc_stop function i leak high level leakage current v pfc_stop =vcc, v dis = 0 v 1a r pfc_stop on-state resistance i pfc_stop = 1 ma, v dis = 1.5 v 130 200 v l low saturation level i pfc_stop = 1 ma, v dis = 1.5 v 0.2 v soft-start function i leak open-state current v(css) = 2 v 0.5 a r discharge resistance v isen > v isenx 120 standby function i dis input bias current v dis = 0 to vth -1 a vth disable threshold voltage falling (1) 1.2 1.24 1.28 v hys hysteresis voltage rising 50 mv delayed shutdown function i leak open-state current v(delay) = 0 0.5 a i charge charge current v delay = 1 v, v isen = 0.85 v 100 150 200 a vth 1 threshold for forced operation at max. frequency voltage rising (1) 1.98 2.05 2.12 v vth 2 shutdown threshold voltage rising (1) 3.35 3.5 3.65 v vth 3 restart threshold voltage falling (1) 0.3 0.33 0.36 v table 5. electrical characteristics (continued)
l6599a electrical characteristics doc id 15308 rev 5 11/36 symbol parameter test condition min. typ. max. unit low-side gate driver (voltages referred to gnd) v lvg l output low voltage i sink = 200 ma 1.5 v v lvg h output high voltage i source = 5 ma 12.8 13.3 v i sourcepk peak source current -0.3 a i sinkpk peak sink current 0.8 a t f fall time 30 ns t r rise time 60 ns uvlo saturation vcc= 0 to vcc on , i sink = 2 ma 1.1 v high-side gate driver (v oltages referred to out) v lvg l output low voltage i sink = 200 ma 1.5 v v lvg h output high voltage i source = 5 ma 12.8 13.3 v i sourcepk peak source current -0.3 a i sinkpk peak sink current 0.8 a t f fall time 30 ns t r rise time 60 ns hvg-out pull-down 25 k 1. values tracking each other table 5. electrical characteristics (continued)
typical electrical performance l6599a 12/36 doc id 15308 rev 5 6 typical electrical performance figure 3. device consumption vs supply voltage figure 4. ic consumption vs junction temperature figure 5. v cc clamp voltage vs junction temperature figure 6. uvlo thresholds vs junction temperature
l6599a typical electrical performance doc id 15308 rev 5 13/36 figure 7. oscillator frequency vs junction temperature figure 8. dead-time vs junction temperature figure 9. oscillator frequency vs timing components figure 10. oscillator ramp vs junction temperature
typical electrical performance l6599a 14/36 doc id 15308 rev 5 figure 11. reference voltage vs junction temperature figure 12. current mirroring ratio vs junction temperature figure 13. ocp delay source current vs junction temperature figure 14. ocp delay thresholds vs junction temperature
l6599a typical electrical performance doc id 15308 rev 5 15/36 figure 15. standby thresholds vs junction temperature figure 16. current sense thresholds vs junction temperature figure 17. line thresholds vs junction temperature figure 18. line source current vs junction temperature 11.5 12 12.5 13 13.5 \ 20 0 20 40 60 80 100 120 pin ? 7 ? (ua) tj ? (c) vcc ? = ? 15v
typical electrical performance l6599a 16/36 doc id 15308 rev 5 figure 19. latched disable threshold vs junction temperature
l6599a application information doc id 15308 rev 5 17/36 7 application information the l6599a is an advanced double-ended controller specific for resonant half-bridge topology (see figure 21. ). in these converters the switches (mosfets) of the half-bridge leg are alternately switched on and off (180 out-of-phase) for exactly the same time. this is commonly referred to as operat ion at ?50% duty cycle?, although the real duty cycle, that is the ratio of the on-time of either switch to the switching period, is actually less than 50%. the reason is that there is an internally fixed dead-time t d inserted between the turn-off of either mosfet and the turn-on of the other one, where both mosfets are off. this dead- time is essential in order for the converter to work correctly: it will ensure soft-switching and enable high-frequency operation with high efficiency and low emi emissions. to perform converter's output voltage regulation the device is able to operate in different modes ( figure 20 ), depending on the load conditions: 1. variable frequency at heavy and medium/ light load. a relaxation oscillator (see section 7.1: oscillator for more details) generates a symmetrical triangular waveform, which mosfets' switching is locked to. the fr equency of this waveform is related to a current that will be modul ated by the feedback circuitry. as a result, the tank circuit driven by the half-bridge will be stimulated at a frequency dictated by the feedback loop to keep the output voltage regulated, thus exploiting its frequency-dependent transfer characteristics. 2. burst-mode control with no or very light load. when the load falls below a value, the converter will enter a controlle d intermittent operation, where a series of a few switching cycles at a nearly fixed frequency are spaced out by long idle periods where both mosfets are in off-state. a further load decrease will be translated into longer idle periods and then in a reduction of the average switching frequency. when the converter is completely unloaded, the average switching frequency can go down even to few hundred hertz, thus minimizing magnetizing current losses as well as all frequency-related losses and making it easier to comply with energy saving recommendations. figure 20. multi-mode operation of the l6599a !-v f sw 0 in 6ariable frequencymode 0inma x "urs t mode 6 in
application information l6599a 18/36 doc id 15308 rev 5 figure 21. typical system block diagram 7.1 oscillator the oscillator is programmed ex ternally by means of a capaci tor (cf), connec ted from pin 3 (cf) to ground, that will be al ternately charged and discharged by the current defined with the network connected to pin 4 (rfmin). the pin provides an accurate 2 v reference with about 2 ma source capability an d the higher the current sourc ed by the pin is, the higher the oscillator frequency will be . the block diagram of figure 22 shows a simplified internal circuit that explains the operation. the network that loads the rfmin pin generally comprises three branches: 1. a resistor rfmin connected between the pin and ground that determines the minimum operating frequency; 2. a resistor rfmax connected between the pin and the collector of the (emitter- grounded) phototransistor that transfers the feedback signal from the secondary side back to the primary side; while in oper ation, the phototransistor will modulate the current through this branch - hence modula ting the oscillator frequency - to perform output voltage regulation; the value of rfmax determines the maximum frequency the half-bridge will be operated at when th e phototransistor is fully saturated; 3. an r-c series circuit (css+rss) connected between the pin and ground that enables to set up a frequency shift at start-up (see section 7.3: soft-start ). note that the contribution of this branch is zero during steady-state operation. !-v 6 inac 6 outdc $!0 2esonant("isturnedoffincaseof 0&#gsanomalousoperationforsafety 0&#canbeturnedoffatlight loadtoeasecompliancewith energysavingregulations $!0 % ' $ ) 2 " & , ! ( 4 . ! . / 3 % 2 , ! . / ) 4 0 / 2 / 4 ! , 5 ' % 2 % 2 0 # & 0 $!0! 6 inac 6 outdc $!0 2esonant("isturnedoffincaseof 0&#gsanomalousoperationforsafety 0&#canbeturnedoffatlight loadtoeasecompliancewith energysavingregulations $!0 % ' $ ) 2 " & , ! ( 4 . ! . / 3 % 2 , ! . / ) 4 0 / 2 / 4 ! , 5 ' % 2 % 2 0 # & 0 $!0! ,! , 6 inac 6 outdc $!0 2esonant("isturnedoffincaseof 0&#gsanomalousoperationforsafety 0&#canbeturnedoffatlight loadtoeasecompliancewith energysavingregulations $!0 % ' $ ) 2 " & , ! ( 4 . ! . / 3 % 2 , ! . / ) 4 0 / 2 / 4 ! , 5 ' % 2 % 2 0 # & 0 $!0! 6 inac 6 outdc $!0 2esonant("isturnedoffincaseof 0&#gsanomalousoperationforsafety 0&#canbeturnedoffatlight loadtoeasecompliancewith energysavingregulations $!0 % ' $ ) 2 " & , ! ( 4 . ! . / 3 % 2 , ! . / ) 4 0 / 2 / 4 ! , 5 ' % 2 % 2 0 # & 0 $!0! ,! ,,! ,3,( ,
l6599a application information doc id 15308 rev 5 19/36 figure 22. oscillator's internal block diagram the following approximate relati onships hold for the minimu m and the maximum oscillator frequency respectively: equation 1 after fixing cf in the hundred pf or in the nf (consistently with the maximum source capability of the rfmin pin and trading this of f against the total consumption of the device), the value of rf min and rf max will be selected so that the oscillator frequency is able to cover the entire range needed for regulation, from the minimum value f min (at minimum input voltage and maximum load) to the maximum value f max (at maximum input voltage and minimum load): equation 2 a different selection crit erion will be given for r fmax in case burst-mode operation at no-load will be used (see section 7.2: operation at no load or very light load ). 6 2&min #& 3 1 2 6 6 #& ) 2 q+ - q) 2 + - q) 2 2&min + - q) 2 2ss 2 &max #ss ,! 6 2&min #& 3 1 2 6 6 #& ) 2 q+ - q) 2 + - q) 2 2&min + - q) 2 2ss 2 &max #ss 6 2&min #& 3 1 2 6 6 #& ) 2 q+ - q) 2 + - q) 2 2&min + - q) 2 2ss 2 &max #ss ,! 6 2&min #& 3 1 2 6 6 #& ) 2 q+ - q) 2 + - q) 2 2&min + - q) 2 2ss 2 &max #ss !-v () max min max min min rf // rf cf 3 1 f ; rf cf 3 1 f ? ? = ? ? = 1 f f rf rf ; f cf 3 1 rf min max min max min min ? = ? ? =
application information l6599a 20/36 doc id 15308 rev 5 figure 23. oscillator waveforms and their relationship with gate-driving signals in figure 23 the timing relationship between the os cillator waveform and the gate-drive signal, as well as the swinging node of the half-bridge leg (hb) is shown. note that the low- side gate-drive is turned on while the oscillator's triangle is ramping up and the high-side gate-drive is turned on while the triangle is ramping down. in this way, at start-up, or as the ic resumes switching during burst-mode operation, the lo w-side mosfet will be switched on first to charge the bootstrap capacitor. as a result, the bootstrap capacitor will always be charged and ready to supply the high-side floating driver. 7.2 operation at no lo ad or very light load when the resonant half-bridge is lightly loaded or unloaded at all, its switching frequency will be at its maximum value. to keep the output vo ltage under control in these conditions and to avoid losing soft-switching, there must be some significant residual current flowing through the transformer's magnetizing inductance. this current, however, produces some associated losses that prevent converter's no-load consumption from achieving very low values. to overcome this issue, the l6599a enables the designer to make the converter operate intermittently (burst-mode operation), with a se ries of a few switching cycles spaced out by long idle periods where both mosfets are in off-state, so that the average switching frequency can be substantially reduced. as a result, the average value of the residual magnetizing current a nd the associated losses will be considerably cut down, thus facilitating the converter to comply with energy saving recommendations. the l6599a can be operated in burst-mode by using pin 5 (stby): if the voltage applied to this pin falls below 1.24 v the ic will enter an idle state where both gate-drive outputs are low, the oscillator is st opped, the soft-start ca pacitor css keeps its charge and only the 2 v reference at rfmin pin stays alive to minimize ic's consumption and vcc capacitor's discharge. the ic will re sume normal operation as the volt age on the pin exceeds 1.24 v by 50 mv. to implement burst-mode operation the voltage applied to the stby pin needs to be related to the feedback loop. figure 24 a shows the simplest implementation, suitable with a narrow input voltage range (e.g. when there is a pfc front-end). !-v #& (6' t t ,6' t (" t 4 $ 4 $
l6599a application information doc id 15308 rev 5 21/36 figure 24. burst-mode implementation: a) narrow input voltage range; b) wide input voltage range essentially, rf max will define the switching frequency fmax above which the l6599a will enter burst-mode operation. once fixed fmax, rf max will be found from the relationship: equation 3 note that, unlike the f max considered in the previous section (? section 7.1: oscillator ?), here f max is associated to some load pout b greater than the minimum one. pout b will be such that the transformer's peak currents are low enough not to cause audible noise. resonant converter's switching frequency, however, depends also on the input voltage; hence, in case there is quite a large input voltage range with the circuit of figure 24 a the value of pout b would change considerably. in this case it is recommended to use the arrangement shown in figure 24 b, where the information on the converter's input voltage is added to the voltage applied to the stby pin. due to the strongly non-linear relationship between switching frequency and input voltage, it is more practical to find empirically the right amount of correction r a / (r a + r b ) needed to minimize the change of pout b . just be careful in choosing the total value r a + r b much greater than r c to minimize the effect on the line pin voltage (see section 7.6: line sensing function ). whichever circuit is in use, its operation can be described as follows. as the load falls below the value pout b the frequency will try to exceed the maximum pr ogrammed value fmax and the voltage on the stby pin (v stby ) will go below 1.24 v. the ic will then stop with both gate-drive outputs low, so that both mosfets of the half-bridge leg are in off-state. the voltage v stby will now increase as a result of the f eedback reaction to the energy delivery stop and, as it exceeds 1. 29 v, the ic will restart switching. after a while, v stby will go down again in response to th e energy burst and stop the ic. in th is way the converter will work in a burst-mode fashion with a nearly constant sw itching frequency. a furt her load decrease will then cause a frequency reduction, which can go down even to few hundred hertz. the timing diagram of figure 25 illustrates this kind of operation, sh owing the most significant signals. a small capacitor (typically in the hundred pf) from the stby pin to ground, placed as close to the ic as possible to reduce switching noise pick-up, will help get clean operation. to help the designer meet energy saving re quirements even in power-factor-corrected systems, where a pfc pre-regulator precedes the dc-dc converter, the l6599a allows that the pfc pre-regulator can be turned off during burst-mode operation, hence eliminating the !-v d e '$3 67%< 5)plq 5 )plq 5 )pd[ '$3 67%< 5)plq 5 )plq 5 )pd[ /,1( 5 $ % 5 % 5 & 5 ' 5 $ 5 % !!5 & /$ /$ d e '$3 67%< 5)plq 5 )plq 5 )pd[ '$3 67%< 5)plq 5 )plq 5 )pd[ /,1( 5 $ % 5 % 5 & 5 ' 5 $ 5 % !!5 & /$ /$ 1 f f rf 8 3 rf min max min max ? =
application information l6599a 22/36 doc id 15308 rev 5 no-load consumption of this stage (0.5 1 w). there is no compliance issue in that because emc regulations on low-frequency harmonic emissions refer to nominal load, no limit is envisaged when the converter operates with light or no load. to do so, the l6599a provides pin 9 (pfc_stop): it is an open collector output, normally open, that is asserted low when the ic is idle during burst-m ode operation. this signal will be externally used for switching off the pfc controller and the pre-regulator as shown in figure 26 . when the l6599a is in uvlo the pin is kept open, to let the pfc controller start first figure 25. load-dependent operating modes: timing diagram figure 26. how the l6599a can switch off a pfc controller at light load 67%< 9 w i rvf p9 k\vwhu /9* +9* w w 3)&b6723 5hvrqdqw0rgh %xuvwprgh 5hvrqdqw0rgh 3)& *$7('5,9( !-v !-v ,! 0&#?34/0 ,! 6cc ).6 k a k a "# "# ,! 0&#?34/0 ,!3( 0&#?/+ !#?/+ ,! 0&#?34/0 ,! 6cc ).6 k a k a "# "# ,! 0&#?34/0 ,!3( 0&#?/+ !#?/+
l6599a application information doc id 15308 rev 5 23/36 7.3 soft-start generally speaking, purpose of soft-start is to progressively increase converter's power capability when it is started up, so as to avoid excessive inrush current. in resonant converters the deliverable power depends inversely on frequency, then soft- start is done by sweeping the operating frequency from an initial high value until the control loop takes over. with the l6599a converter's soft start-up is simply realized with the addition of an r-c series circuit from pin 4 (rfmin) to ground (see figure 27 , left). initially, the capacitor css is tota lly discharged, so that the seri es resistor rss is effectively in parallel to rfmin and the resulting initial frequency is determined by rss and rfmin only, since the optocoupler's phototransistor is cut off (as long as the output voltage is not too far away from the regulated value): equation 4 the c ss capacitor is progressively charged until its voltage reaches the reference voltage (2 v) and, consequently, the current through r ss goes to zero. this conventionally takes 5 times constants r ss c ss but, before that time, the output voltage will have got close to the regulated value and the feedback loop taken ov er, so that it will be the optocoupler's phototransistor to determine the operating frequency from that moment onwards. during this frequency sweep phase the operating frequency will decay following the exponential charge of c ss , that is, initially it will change relatively quickly but the rate of change will get slower and slow er. this counteract the non- linear frequency dependence of the tank circuit that makes converter's power capability chan ge little as freq uency is away from resonance and change very quickly as frequency approaches resonance frequency (see figure 27 , right). figure 27. soft-start circuit (left) and power vs. frequency curve in an resonant half-bridge (right) as a result, the average input current will smoo thly increase, without the peaking t hat occurs with linear frequency sweep, and the outp ut voltage will reach th e regulated value with almost no overshoot. typically, r ss and c ss will be selected based on the following relationships: () ss min start r // rf cf 3 1 f ? ? = !-v ,! #ss 2&min 2 &min 2 33 # 33 2%3/.!.#% &2%15%.#9 f \:f \ )nitial frequency 3teady state frequency
application information l6599a 24/36 doc id 15308 rev 5 equation 5 where f start is recommended to be at least 4 times f min . the proposed criterion for c ss is quite empirical and is a compromise between an effective soft-start action and an effective ocp (see next section). please refer to the timing diagram of figure 27 to see some significant signals during the soft-start phase. 7.4 current sense, ocp and olp the resonant half-bridge is e ssentially voltage-mode controlled; hence a current sense input will only serve as an overcu rrent protection (ocp). unlike pwm-controlled converters, where energy fl ow is controlled by the duty cycle of the primary switch (or switches), in a resonant half -bridge the duty cycle is fixed and energy flow is controlled by its switching frequency. this impacts on the way current limitation can be realized. while in pw m-controlled converters energy flow can be limited simply by terminating switch conduction beforehand when the sensed current exceeds a preset threshold (this is commonly now as cycle-by- cycle limitation), in a resonant half-bridge the switching frequency, that is, its oscillator?s frequency must be increased and this cannot be done as quickly as turning off a switch: it take s at least the next osc illator cycle to see the frequency change. this implies that to have an effective increase, able to change the energy flow significantly, the rate of change of th e frequency must be slower than the frequency itself. this, in turn, implies that cycle-by-cycle limitation is not feasible and that, therefore, the information on the primary current fed to the current sensing input must be somehow averaged. of course, the averaging time must not be too long to prevent the primary current from reaching too high values. in figure 28 a couple of current sensin g methods are illustrated that will be described in the following. the circuit of figure 28 a is simpler but the dissipation on the sense resistor rs might not be negligible, hurting efficiency; the circuit of figure 28 b is more complex but virtually lossless and recommended when the efficiency target is very high. ss 3 ss min start min ss r 10 3 c ; 1 f f rf r ? ? = ? =
l6599a application information doc id 15308 rev 5 25/36 figure 28. current sensing techniques: a) with sense resistor, b) ?lossless?, with capacitive shunt the l6599a is equipped with a current sensing input (pin 6, isen) and a sophisticated overcurrent management system. the isen pin is internally connected to the input of a first comparator, referenced to 0.8 v, and to that of a second comparator referenced to 1.5 v. if the voltage externally applied to the pin by either circuit in figure 28 exceeds 0.8 v the first comparator is tripped and this causes an inte rnal switch to be turned on and discharge the soft-start capacitor c ss (see section 7.3: soft-start ). this will quickly in crease the oscillator frequency and th ereby limit energy transfer. the discha rge will go on until the voltage on the isen pin has dropped by 50 mv; this, with an averaging time in the range of 10/f min , ensures an effective frequency rise. under output short circuit, this operation results in a nearly constant peak primary current. it is normal that the voltage on the isen pin may overshoot above 0.8 v; however, if the voltage on the isen pin reaches 1.5 v, the se cond comparator will be triggered, the l6599a will shutdown and latch off with both the gate -drive outputs and the pfc_stop pin low, hence turning off the entire unit. the supply voltage of the ic must be pulled below the uvlo threshold and then again above the start-up level in order to restart. such an event may occur if the soft-start capacitor c ss is too large, so that its discharge is not fast enough or in case of transformer?s magnetizing inductance saturation or a shorted secondary rectifier. in the circuit shown in figure 28 a, where a sense resistor rs in series to the source of the low-side mosfet is used, note the particular connection of the resonant capacitor. in this way the voltage across rs is related to the current flowing through the high-side mosfet and is positive most of the switching period, except for the time needed for the resonant current to reverse after the low-side mosfet has been switched off. assuming that the time constant of the rc filter is at least ten times the minimum switching frequency f min , the approximate value of rs can be found using the empirical equation: equation 6 where i crpkx is the maximum desired peak current flowing through the resonant capacitor and the primary winding of the transformer, which is related to the maximum load and the minimum input voltage. !-v d e '$3 ,6(1 t z i plq 5v &u 9vsn , &u '$3 ,6(1 &u 5 $ 5 % 1 & % & $ 1 t z i plq 9 &usn , &u /$ /$ d e '$3 ,6(1 t z i plq 5v &u 9vsn , &u '$3 ,6(1 &u 5 $ 5 % 1 & % & $ 1 t z i plq 9 &usn , &u /$ /$ crpkx crpkx crpkx pkx i 4 i 8 . 0 5 i vs rs ? =
application information l6599a 26/36 doc id 15308 rev 5 the circuit shown in figure 28 b can be operated in two different ways. if the resistor r a in series to c a is small (not above some hundred , just to limit curren t spiking) the circuit operates like a capacitive current divider; c a will be typically select ed equal to cr/100 or less and will be a low-loss type, the sense resistor r b will be selected as: equation 7 and c b will be such that r b c b is in the range of 10 /f min . if the resistor r a in series to c a is not small (in this case it w ill be typically sele cted in the ten k ), the circuit operates like a divider of the ripple voltage across the resonant capacitor cr, which, in turn, is related to its current through the reactance of cr. again, c a will be typically selected equal to cr/100 or less, this ti me not necessarily a lo w-loss type, while r b (provided it is << r a ) according to: equation 8 where the reactance of c a (x ca ) and cr (x cr ) should be calculated at the frequency where i crpk = i crpkx . again, c b will be such that r b c b is in the range of 10 /f min . whichever circuit one is going to use, the calculated values of rs or r b should be considered just a first cut value that needs to be adjusted after experimental verification. ocp is effective in limiting primary-to-secondary energy flow in case of an overload or an output short circuit, but the output current through the secondary winding and rectifiers under these conditions might be so high to endanger converter?s safety if continuously flowing. to prevent any damage during these conditions it is customary to force converter?s intermittent operation, in order to bring the av erage output current to values such that the thermal stress for the transformer and the rectifiers can be easily handled. with the l6599a the designer can program externally the maximum time t sh that the converter is allowed to run overloaded or under short circuit conditions. overloads or short circuits lasting less than t sh will not cause any other action , hence providing the system with immunity to short duration phenomena. if, instead, t sh is exceeded an overload protection (olp) procedure is activated that shuts down the l6599a and, in case of continuous overload/short circuit, results in continuous intermittent operation with a user- defined duty cycle. ? ? ? ? ? ? ? ? + = a r crpkx b c c 1 i 8 . 0 r cr 2 c 2 a crpkx b x x r i 8 . 0 r a + =
l6599a application information doc id 15308 rev 5 27/36 figure 29. soft-start and delayed shutdown upon overcurrent timing diagram this function is realized with pin 2 (delay), by means of a capacitor c delay and a parallel resistor r delay connected to ground. as the voltage on the isen pin exceeds 0.8 v the first ocp comparator, in addition to discharging c ss , turns on an internal current generator that sources 150 a from the delay pin and charges c delay . during an overload/short-circuit the ocp comparator and the in ternal current source will be repeatedly activated and c delay will be charged with an average cu rrent that depends es sentially on the time constant of the current sense filtering circuit, on c ss and the characteristics of the resonant circuit; the discharge due to r delay can be neglected, considering that the associated time constant is typically much longer. this operation will go on until the voltage on c delay reaches 2 v, which defines the time t sh . there is not a simple re lationship that links t sh to c delay , thus it is more practical to determine c delay experimentally. as a rough indication, with c delay = 1 f t sh will be in the order of 100 ms. once c delay is charged at 2 v the internal switch that discharges c ss is forced low continuously regardless of the ocp comparator?s output, and the 150 a current source is continuously on, until the voltage on c delay reaches 3.5 v. this phase lasts: equation 9 with t mp is expressed in ms and c delay in f. during this time the l6599a runs at a frequency close to f start (see section 7.3: soft-start ) to minimize the energy inside the resonant circuit. as the voltage on c delay is 3.5v, the l6599a stops switching and the pfc_stop pin is pulled low. also the internal generator is turned off, so that c delay will now be slowly discharged by r delay . the ic will restart when the voltage on c delay will be less than 0.3 v, which will take: equation 10 !-v w 9ff &vv w w '(/$< 67$5783 29(5 /2$' 29(5/2$' w 3ulpdu\ &xuuhqw 1250$/ 23(5$7,21 1250$/ 23(5$7,21 6+87'2:1 9 9rxw w $ 62)767$57 62)767$57 9 9 9 0,132:(5 w 3)&b6723 ,6(1 w 9 7 6+ 7 6723 7 03 7 vv delay mp c 10 t ? = delay delay 3 . 0 5 . 3 delay delay stop c r 5 . 2 ln c r t =
application information l6599a 28/36 doc id 15308 rev 5 the timing diagram of figure 29 shows this operation. note that if during t stop the supply voltage of the l6599a (vcc) falls below the uvlo threshold the ic keeps memory of the event and will not restart immedi ately after vcc exceeds the star t-up threshold if v(delay) is still higher than 0.3 v. also the pfc_stop pin will stay low as long as v(delay) is greater than 0.3 v. note also that in case there is an overload lasting less than t sh , the value of t sh for the next overload will be lower if they are close to one another. 7.5 latched shutdown the l6599a is equipped with a comparator having the non-inverting input externally available at pin 8 (dis) and with the inverting input internally referenced to 1.85v. as the voltage on the pin exceeds the internal threshold, the ic is immediately shut down and its consumption reduced at a low value. the information is latched and it is necessary to let the voltage on the vcc pin go below the uvlo threshold to reset the latch and restart the ic. this function is useful to implement a latched overtemperature protection very easily by biasing the pin with a divider from an external reference voltage (e.g. pin 4, rfmin), where the upper resistor is an ntc physically loca ted close to a heating element like the mosfet, or the secondary diode or the transformer. an ovp can be implemented as well, e.g. by se nsing the output voltage and transferring an overvoltage condition via an optocoupler. 7.6 line sensing function this function basically stops the ic as the input voltage to the co nverter falls below the specified range and lets it restart as the vo ltage goes back within the range. the sensed voltage can be either the rectif ied and filtered mains voltage, in which case th e function will act as a brownout protection, or, in systems with a pfc pre-regulator front-end, the output voltage of the pfc stage, in which case the fu nction will serve as a power-on and power-off sequencing. l6599a shutdown upon input undervoltage is accomplished by means of an internal comparator, as shown in the block diagram of figure 30 , whose non-inverting input is available at pin 7 (line). the comparator is inte rnally referenced to 1.24 v and disables the ic if the voltage applied at the line pin is below the internal reference. under these conditions the soft-start is discharged, the pfc_stop pin is open and the consumption of the ic is reduced. pwm operation is re-ena bled as the voltage on the pin is above the reference. the comparator is provided with current hysteresis instead of a more usual voltage hysteresis: an internal 13 a current sink is on as long as the voltage applied at the line pin is below the reference and is of f if the voltage is above the reference. this approach provides an additional degree of freedom: it is possible to set the on threshold and the off threshold separately by properly choosing the resistors of the external divider (see below). with voltage hysteresis, instead, fixing one threshold automatically fixes the other one depending on the built-in hysteresis of the comparator.
l6599a application information doc id 15308 rev 5 29/36 figure 30. line sensing function: internal block diagram and timing diagram with reference to figure 28 , the following relationships can be established for the on (vin on ) and off (vin off ) thresholds of the input voltage: equation 11 which, solved for r h and r l , yield: equation 12 while the line undervoltage is active the start-up generator keeps on working but there is no pwm activity, thus the vcc voltage (if not supplied by another source) continuously oscillates between the start-up and the uvlo thresholds, as sh own in the timing diagram of figure 30 . as an additional measure of safety (e.g. in case the low-side resistor is open or missing, or in non-power factor corrected systems in case of abnormally high input voltage) if the voltage on the pin exceeds 7 v the l6599a is shut down. if its supply voltage is always above the uvlo threshold, the ic will rest art as the voltage falls below 7 v. the line pin, while the device is operating, is a high impedance input connected to high value resistors, thus it is prone to pick up no ise, which might alter the off threshold or give origin to undesired switch-off of the ic during esd tests. it is possible to bypass the pin to ground with a small film capacitor (e.g. 1-10 nf) to prevent any malfunction ing of this kind. if !-v ,! 6in/+ (6)nputbus 6 ,).% 6cc 6 ?! 2 ( 2 , (6)nputbus 6in/+ 6cc 6in /. 6in /&& ,6' (6' 6out ,).% 6 ) (93 ?! t t t t t t t ,! 6in/+ (6)nputbus 6 ,).% 6cc 6 ?! 2 ( 2 , (6)nputbus 6in/+ 6cc 6in /. 6in /&& ,6' (6' 6out ,).% 6 ) (93 ?! t t t t t t t l h off l 6 h on r 24 . 1 r 24 . 1 vin r 24 . 1 10 13 r 24 . 1 vin = ? + ? = ? ? 24 . 1 vin 24 . 1 r r ; 10 13 vin vin r off h l 6 off on h ? = ? ? = ?
application information l6599a 30/36 doc id 15308 rev 5 the function is not used the pin has to be connected to a voltage greater than 1.24 v but lower than 6v (worst-case value of the 7 v threshold). 7.7 bootstrap section the supply of the floating high-side section is obtained by means of a bootstrap circuitry. this solution normally requires a high voltage fast recovery diode (d boot , figure 31 a) to charge the bootstrap capacitor c boot . in the l6599a a patented integrated structure, replaces this external diode. it is realized by means of a high voltage dmos, working in the third quadrant and driven synchronously with the low side driver (lvg), with a diode in series to the source, as shown in figure 31 b. figure 31. bootstrap supply: a) standard circuit; b) internal bootstrap synchronous diode the diode prevents any current can flow from the vboot pin back to vcc in case that the supply is quickly turned off when the internal capacitor of the pump is not fully discharged. to drive the synchronous dmos it is necessary a voltage higher than the supply voltage vcc. this voltage is obtained by means of an internal charge pump ( figure 31 b). the bootstrap structure introduces a voltage dr op while recharging cboot (i.e. when the low side driver is on), which increases with the operating frequency and with the size of the external power mos. it is the sum of the drop across the r (ds)on and the forward drop across the series diode. at low frequency this drop is very small and can be neglected but, as the operating frequency increases, it must be taken into account. in fact, the drop reduces the amplitude of the driving signal and can significantly increase the r (ds)on of the external high-side mosfet and then its conductive loss. this concern applies to converters designed with a high resonance frequency (indicatively, > 150 khz), so that they run at high frequency also at full load. otherw ise, the converter will run at high frequency at light load, where the current flowing in the mosfets of the half- bridge leg is low, so that, generally, an r (ds)on rise is not an issue. however, it is wise to check this point anyway and the following equation is useful to compute the drop on the bootstrap driver: !-v d e 287 9%227 9ff ' %227 & %227 '$3 287 9%227 9ff /9* & %227 /$ d e 287 9%227 9ff ' %227 & %227 '$3 287 9%227 9ff /9* & %227 /$
l6599a application information doc id 15308 rev 5 31/36 equation 13 where qg is the gate charge of the external power mos, r (ds)on is the on-resistance of the bootstrap dmos (150 w, typ.) and t charge is the on-time of the bootstrap driver, which equals about half the switching period minus the dead time t d . for example, using a mosfet with a total gate charge of 30nc, the drop on the bootstrap driver is about 3 v at a switching frequency of 200 khz: equation 14 if a significant drop on the bootstrap driver is an issue, an external ultra-fast diode can be used, thus saving the drop on the r (ds)on of the internal dmos. f on ) ds ( e arg ch g f on ) ds ( e arg ch drop v r t q v r i v + = + = v 7 . 2 6 . 0 150 10 27 . 0 10 5 . 2 10 30 v 6 6 9 drop = + ? ? ? ? = ? ? ?
application information l6599a 32/36 doc id 15308 rev 5 figure 32. application example: 90w ac/dc adapter using l6563h, l6599a and srk2000 !-v
l6599a package mechanical data doc id 15308 rev 5 33/36 8 package mechanical data in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions an d product status are available at: www.st.com . ecopack ? is an st trademark. figure 33. dip16 mechanical data dip16 dim. mm inch min. typ. max. min. typ. max. a1 0.51 0.020 b 0.77 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 d 20 0.787 e 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 f 7.1 0.280 i 5.1 0.201 l 3.3 0.130 z 1.27 0.050 outline and mechanical data
package mechanical data l6599a 34/36 doc id 15308 rev 5 figure 34. so16n mechanical data outline and mechanical data dim. mm inch min. typ. max. min. typ. max. a 1.75 0.069 a1 0.1 0.25 0.004 0.009 a2 1.6 0.063 b 0.35 0.46 0.014 0.018 b1 0.19 0.25 0.007 0.010 c 0.5 0.020 c1 45 (typ.) d (1) 9.8 10 0.386 0.394 e 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 8.89 0.350 f (1) 3.8 4.0 0.150 0.157 g 4.60 5.30 0.181 0.208 l 0.4 1.27 0.150 0.050 m 0.62 0.024 s8 (max.) (1) "d" and "f" do not include mold flash or protrusions - mold flash or protrusions shall not exceed 0.15mm (.006inc.) so16 (narrow) 0016020 d
l6599a revision history doc id 15308 rev 5 35/36 9 revision history table 6. document revision history date revision changes 19-jan-2009 1 initial release 25-feb-2009 2 updated table 5 on page 9 13-mar-2009 3 updated data on table 5 on page 9 under oscillator section 30-oct-2009 4 updated table 5 on page 9 28-sep-2010 5 added: section 6 on page 12
l6599a 36/36 doc id 15308 rev 5 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by an authorized st representative, st products are not recommended, authorized or warranted for use in milita ry, air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2010 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of L6599ADTR

	To Download L6599ADTR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .